Key points for selecting multi-layer wooden flooring

TIME:2026-09-22 10:01:13

1、 Surface veneer (determines texture and can be refurbished)

1. Thickness
-Home preference: ≥ 1.2mm, light scratches can be polished and refurbished, strong three-dimensional wood grain effect
-0.6mm: Engineering board, thin wood veneer, exposed substrate when worn off, cannot be refurbished, try not to use for home use as much as possible
2. Types of veneer: oak, white wax, black walnut, longan, etc., depending on personal preference; Focus on whether the veneer is whole or pieced together, as the wood grain is messy when pieced together.
3. Craftsmanship: Prioritize natural wood veneer; Be wary of technology veneer (recombinant wood, also considered compliant, but with lower prices and repetitive textures)

2、 Substrate (determines stability, moisture resistance, and is of utmost importance)

Look at the side profile of the board!

-Eucalyptus wood substrate: mainstream for home decoration, good stability, high cost-effectiveness
-All birch wood substrate: the best stability, high density, strong moisture resistance, and relatively high price
-Mixed wood/crushed material filling substrate: chaotic layers, holes, blackening, easy to be affected by moisture and deformed, low-priced pit style

Sectional standard: uniform layering, consistent thickness of veneer, no voids, blackening, bark residue, tightly bonded without delamination.

3、 Environmental protection level

Identify the testing report, don't just listen to verbal propaganda

-ENF level: currently the highest national standard (formaldehyde emission ≤ 0.025mg/m ³), priority should be given to selecting
-E0 level: ≤ 0.050mg/m ³, sufficient for household use

Attention: Please refer to the 1 ㎡ sample testing report instead of the full box report; The amount of multi-layer adhesive is more than three layers, so don't ignore environmental protection.

4、 Paint surface and wear resistance (scratch resistant, dirt resistant)

1. Paint type: Matte/semi matte is more recommended, with less noticeable scratches; A slight scratch on the highlight is very noticeable.
2. Wear resistant RPM: A household RPM of ≥ 4000 is sufficient (multi-layer non reinforced flooring, no need to pursue high RPM)
3. Surface technology: Check for anti fouling and waterproof coatings; Lightly scratch the sample with a coin to see if there are any marks easily left.

5、 Locking process (related to installation, anti cracking)

Choose a large angle lock buckle/strong lock buckle, with deep interlocking and not easy to separate from the seam;
On site trial assembly: Two boards are fastened together and forcefully broken, and the gap will not easily open.

Ordinary flat buckle: Installation requires gluing, which is prone to cracking in the later stage, and it is rarely selected for home decoration nowadays.

6、 Size specifications

-Conventional: 1220 × 195 × 15mm; the large board is longer, wider, and has a higher appearance, but it requires higher ground flatness and is more prone to slight gaps.

Floor heating environment: Priority is given to regular sizes, and it is not recommended to use excessively long or wide boards.

7、 Moisture resistance performance (key focus on the south/first floor)

1. The higher the density of the substrate, the better the moisture resistance; Priority eucalyptus/birch wood
2. Check if there is waterproof edge sealing: Apply sealing paint on all four sides of the board to prevent moisture from entering from the sides

First floor, humid area: The bare floor is not sufficiently moisture-proof, and the floor should be treated with moisture-proof measures and covered with moisture-proof film.

8、 Auxiliary materials+after-sales service (many people overlook it, especially in areas severely affected by car accidents)

1. Damp proof pad: ordinary 2mm; special floor heating damp proof pad (heat conduction type) shall be selected for floor heating instead of ordinary thick foam pad, which will hinder heat dissipation.
2. Ask clearly: whether installation is included, how to leave expansion joints, and whether there are additional charges for skirting boards/buckles;
3. Warranty: Distinguish between sheet metal warranty and installation warranty, and retain the contract and inspection report.

9、 Avoiding pitfalls reminder

1. Don't just look at the surface of the sample! Be sure to look at the side profile of the board and distinguish the quality of the substrate at a glance
2. Beware of low-priced "multi-layer": Some are paper veneer, not solid wood veneer
3. underfloor heating users: ENF priority, stable base material, reject miscellaneous wood base materials; It is not recommended to lay dragon bones